SMA RF Attenuator

SMA RF Attenuator

We are searching data for your request:

Forums and discussions:
Manuals and reference books:
Data from registers:
Wait the end of the search in all databases.
Upon completion, a link will appear to access the found materials.

SMA attenuators are easily available and can easily be dropped into a circuit that uses SMA connectors.

The SMA attenuators have SMA connections - SMA male at one end and SMA female at the other. In this way, the SMA attenuator can drop into an existing system using SMA connectors or for new circuits it can keep the same connector type throughout enabling a reduction in different types of connector.

The other advantage of SMA connectors is that they are compact - if no additional heatsink is needed, they take up little more space than the two connectors themselves.

SMA connectors

SMA connectors are widely used, especially for microwave RF applications. Their small size and high RF performance makes them ideal for connections between modules or assemblies within units of RF systems. The small diameter coax used with them means that coax losses are comparatively high, but for short interconnections this is quite acceptable. To provide the required RF performance, these connectors are often gold plated.

The connectors have a threaded outer coupling interface that has a hexagonal shape, allowing it to be tightened with a spanner. Special torque spanners are available to enable them to be tightened to the correct tightness, allowing a good connection to be made without over-tightening them. The torque required is typically 8 inch pounds.

SMA connectors are designed to have a constant have a 50 ohm impedance across the connector. The SMA connectors are designed and specified for operation up to 12.4 GHz, although many high quality versions are useable up to 18 GHz. Also it may be possible to sue them to 24 GHz with a greater level of loss and a lower return loss. Cheap versions of these connectors will not have the same performance, despite what may often be claimed, however they may still be quite acceptable for many applications.

SMA attenuators - values

SMA attenuators are available with a variety of different levels of attenuation. Figures for some of the more common values are given in the table of attenuation vs power ratio and current / voltage.

Performance Parameters for Common SMA RF Attenuator Variants
SMA attenuator attenuation, dBPower RatioCurrent or Voltage Ratio

SMA attenuator impedance

The impedance of the attenuator is a prime consideration. It is essential that the RF attenuator has the same characteristic impedance as the rest of the system.

As SMA connectors are normally designed for 50 Ω operation, so too are SMA attenuators, but it is worth checking just in case a special has been designed and crept onto the market.

SMA attenuator power handling

SMA attenuators come in a variety power levels. Typically they handles relatively low power levels in view of the size of connector and the coax used.

The standard ones are often rated a 2 watts and these do not have any additional heatsinking, although some power will be removed by the coax. This may be particularly good if solid coax is used with a solid copper tube outer. It is, however, wise not to run these attenuators close to the limit otherwise they will get hot

Some other SMA attenuators have higher power levels, often 10 watts, but these have heatsinks incorporated into the body. When using these permanently in any RF system, due consideration needs to be given to the mechanical constraints as the weight of the heatsink will place strain on the connectors, especially if there is any vibration.

Attenuator frequency response

One of the key aspects of the performance of any attenuator is its frequency response, and as such this applies to SMA attenuators. Although it may not be as critical for some applications, for others it may be important.

Normally the top frequency of operation is given. Above this, the performance will fall.

Attenuator VSWR

Another important aspect of any RF attenuator is the VSWR specification.

The VSWR specification of the SMA attenuator provides a view of the impedance match. It is specified in terms of the VSWR - voltage standing wave ratio. This gives an indication of the amount of reflected power - a perfect match would give a 1:1 ratio.

Most attenuators will be specified to provide a VSWR lower than 1.2:1 and this may be specified in the format ≤1.2. A value of ≤1.5 would be adequate for many applications.

Watch the video: #91: Basic RF Attenuators - Design, Construction, Testing - PI and T style - A Tutorial (June 2022).


  1. Khnum

    wonderfully, it is very valuable piece

  2. Vutaxe

    I think I get to correct the decision. Don't despair.

  3. Mauzragore

    You are wrong. Enter we'll discuss. Write to me in PM, we will handle it.

  4. Shajin

    There is something in this. Okay, thank you very much for your help in this matter.

  5. Goltishura

    I agree with you, thanks for the help in this question. As always all ingenious is simple.

  6. Ryszard

    Bravo, what a phrase ... a great thought

Write a message